Electrical and electronics engineering
Electrical engineering Paid promotion @Engineeringupdatess @electricalandelectronics09
Показати більше📈 Аналітичний огляд Telegram-каналу Electrical and electronics engineering
Канал Electrical and electronics engineering (@electricalandelectronics09) у мовному сегменті Англійська є активним учасником. На даний момент спільнота об'єднує 20 065 підписників, посідаючи 6 657 місце в категорії Технології та додатки та 21 189 місце у регіоні Індія.
📊 Показники аудиторії та динаміка
З моменту свого створення невідомо, проект продемонстрував стрімке зростання, зібравши аудиторію у 20 065 підписників.
За останніми даними від 30 червня, 2026, канал демонструє стабільну активність. Хоча за останні 30 днів спостерігається зміна кількості учасників на 169, а за останні 24 години на -1, загальне охоплення залишається високим.
- Статус верифікації: Не верифікований
- Рівень залученості (ER): Середній показник залученості аудиторії становить 35.33%. Протягом перших 24 годин після публікації контент зазвичай збирає 5.43% реакцій від загальної кількості підписників.
- Охоплення публікацій: В середньому кожен допис отримує 0 переглядів. Протягом першої доби публікація в середньому набирає 1 090 переглядів.
- Реакції та взаємодія: Аудиторія активно підтримує контент: середня кількість реакцій на один пост – 0.
- Тематичні інтереси: Контент зосереджений навколо ключових тем, таких як current, transistor, circuit, mosfet, collector.
📝 Опис та контентна політика
Автор описує ресурс як майданчик для висловлення суб'єктивної думки:
“Electrical engineering
Paid promotion @Engineeringupdatess
@electricalandelectronics09”
Завдяки високій частоті оновлень (останні дані отримано 01 липня, 2026), канал підтримує актуальність та високий рівень охоплення публікацій. Аналітика показує, що аудиторія активно взаємодіє з контентом, що робить його важливою точкою впливу в категорії Технології та додатки.
Триває завантаження даних...
| Дата | Залучення підписників | Згадування | Канали | |
| 01 липня | +1 |
| 2 | Немає тексту... | 5 882 |
| 3 | Немає тексту... | 6 335 |
| 4 | Немає тексту... | 8 087 |
| 5 | Немає тексту... | 8 192 |
| 6 | Немає тексту... | 7 681 |
| 7 | Немає тексту... | 0 |
| 8 | Немає тексту... | 0 |
| 9 | Controlling DC motor speed using voltage directly is inefficient, so this circuit uses Pulse Width Modulation (PWM) to do it more effectively. A 555 timer generates a square wave where the ON time and OFF time can be adjusted using the variable resistor (VR1). When the pulse is narrow, the motor receives power for a shorter time, resulting in lower average voltage and slower speed. When the pulse is wide, the motor gets power for longer duration, increasing the average voltage and making it spin faster. The diodes around the potentiometer help control the charge and discharge paths separately, allowing smooth duty cycle adjustment. The output from the 555 timer drives a power transistor (2N3055), which acts like a switch to supply current to the motor. A diode across the motor protects the circuit from voltage spikes generated when the motor turns off. This method provides efficient speed control with minimal power loss.
#ElectronicsEducation #ElectronicsRD #PWM #DCMotor #555Timer
Like share 👍👍😍✨✨ | 0 |
| 10 | Немає тексту... | 0 |
| 11 | This circuit shows how an Arduino controls an RGB LED using three output pins. An RGB LED contains three internal LEDs—Red, Green, and Blue—combined in one package. In this diagram, it is a common cathode type, meaning all the negative terminals are connected together and tied to ground.
Each color pin (R, G, B) is connected to a separate Arduino digital/PWM pin through a 220Ω resistor (R1, R2, R3). These resistors limit current and protect both the LED and the Arduino.
When the Arduino sends a HIGH signal to any pin, current flows through the resistor and the corresponding LED color turns ON. By using PWM (pins marked with ~), the brightness of each color can be adjusted. By mixing different brightness levels of Red, Green, and Blue, a wide range of colors can be produced.
For example:
Red + Green = Yellow
Red + Blue = Magenta
Green + Blue = Cyan
All three = White
This is the basic principle behind color mixing in displays and lighting systems.
#ElectronicsEducation #ElectronicsRD #Arduino #EmbeddedSystems | 0 |
Вже доступно! Дослідження Telegram за 2025 — головні інсайти року 
