1 935
Subscribers
+224 hours
+47 days
+5430 days
Posts Archive
XML for Mi 10 Ultra full resolution mode. Use with Linkon modded Sgcam 8.4 v38. For XML to work you need to put the lib MSL8.so in SGCAM>LIB folder. Lib is also tested with BSG 8.5.
CHANGES 04/07/2023:
-Better RAW files. Less chroma noise and color artefacts. New 48mp noise model activated for 1xN and 1xD. Only works with SGCam mentioned above.
-SOFT mode is now matched with SHARP output in all other aspects but sharpening. SOFT is recommended for landscapes and other scenes with lots of tiny details that easily get unnatural with more sharpening. SHARP is the default output mode; slightly less sharp than MSL7 but gives that somewhat "digital" look.
1. 1x D lens is for daylight. Use with zsl. Stay still for at least 2 seconds before taking a photo in zsl mode for best results. Min. SS 1/20s.
2. 1x N is meant for scenes where highlights need protection.
3. 36 MP / 48 MP button. JPG resizing is meant to be used in full resolution mode. In 12mp sensor mode you will get 9mp files if enabled.
Hi, to all the guys and girls here π
After almost 700 photos and over 4 hours of fine-tuning, I managed to transfer my neutral and warm configurations from the MSL9 to the MSL10 π₯³
(it could have taken much longer if I had started at 0 π€£).
I was only able to do this thanks to the correct lens IDs from Threedog π
Like last time, I only adjusted the Colors and the White Balance for each individual Lens and matched them to each other.
This way you always have almost identical colors, even if you have to change the lens πͺ
(100% won't be possible, but I think it's about 85-90% π€).
I have also taken over the correct black levels from Dennis_al.
I didn't change the Details, Noise Reduction, Brightness and Contrasts, they stayed exactly as Juhana intended.
You will need the following files
Now let's talk briefly about the MSL9: The MSL9 is based on Juhana's work. Threedog was kind enough to make this great setting run on the 11U.
Since I saw a lot of potential here,
I decided to optimize the colors according to the highest standards, so that this setting is also on a par with the LMC config ππͺ
However, I didn't change anything about the look or the Details.
But I have adapted the LDR function to my taste:
With the LDR function activated, you now get a brighter, softer image π
Juhana had already had dedicated buttons for other darker image modes, but in my eyes one was missing that makes the image brighter and softer.
Now there are almost no limits to creativity. Again, there is a choice between the Warm π and the Neutral π‘Configs.
First of all, I would like to introduce you to the LMC configuration and explain it in more detail: This setting was published last year on September 14th by Matteo in XML channel, he worked on it together with Arcide. The name is ArcideMatteo.xml
I discovered this setting and was amazed by the details π
After some time, the colors have been completely revised, because I have really high demands on the colorsπ§
In addition, I have refined the look a bit, so that the picture is a bit softer π
In the course of the time in which I now test settings, I have noticed that unfortunately many use a very strong denoise, which leads to much muddy images in low light.π
Therefore, I have reduced the denoise to a minimum. As a result, the picture is a bit noisy, but you don't lose the natural look of faces, especially in low light π―οΈπ
For now, unfortunately, the LMC R15 has to be usedπ. It is a version adapted by Dennis that contains the correct blacklevels. Since the original XML was created for this version, and I've changed a lot as well, I can't say for sure what problems occur with R17 & R18. But short tests already showed me incompatibilities.
About Fullres
Do you also like to use the Fullres module from time to time? Then you can enable compatibility with a small setting π
Go to : Photo Processing -> Hex Manual -> enable "User Value No 8". In addition, upscaling (activated by default) must be deactivated with the "Res" button. For normal use, simply reload the setting βΊοΈ
After a lot of testing, a lot of photos and the finishing touches, I am now ready to proudly announce that I would like to share my work with you π
In the past, I have only used the Settings privately, because it is not completely my creation π§
A few days ago I got permission from Arcide and Matteo to publish these settingsπ
But First,
About Warm and Neutral :
Since it is virtually impossible to capture 2 of the most common lighting conditions with a neutral to beautiful look with one setting, I have created 2 dedicated settings.
My Warm setting is for all situations where it can be a little warmer, or the pictures you have taken need "that certain something" more.
But the Warm setting has its limits, especially with artificial lightπ‘ in the evening hours, it is too much.
That's exactly why I created the Neutral setting, for situations where warm is too warm, the neutral is just right.
Neutral can be used around the clock ππ‘
It sounds cumbersome, but after some time you will know in advance which setting works now. But a very simple rule:
Never Warm in artificial light, otherwise always warm, unless it is too warm π
Soft option is not working for now on full res XML, it'll be fixed after investigation π
